Tag: Spooky2 Device

In this article, we will introduce a very basic process of copying the frequency of the substance into the water. To start copying the frequency of the treatment into the water, you need:

• Spooky2 XM generator
• Spooky2 Radionics Machine
• Replicated substance and a bottle of distilled water

Substance to be copied

You will need a substance that you wish to copy. In this example, I will use vitamin A capsules. I recommend taking them out of the plastic bottle and placing them in a glass container for copying. You don’t need to copy so many capsules, one capsule is enough. In fact, the information imprint only needs a vitamin A molecule, and you need a fresh distilled water to copy.

Spooky2 Connection and Software

Use the supplied BNC cable to connect Spooky2 XM generator OUT1 to Spooky2 Radionics Input, connect the XM generator USB cable to your PC, and run Spooky2 software. If you do not have a PC and Spooky2 software, in the Spooky2 software, select Radionics from the main preset menu, then select Radionics General Preset, go to the Control tab, then click the generator box, click Start to load the waveform to the generator And start the program. In this preset, it will continue to run until you click Stop.

Frequency Replication Process

When the Spooky2 XM generator is running and connected to the Spooky2 Radionics instrument, the blue LED will light up to indicate that the frequency is being received. Put your capsule on the input board and put the pre-prepared distilled water on the output board. This is all it contains. For this basic copying process, you can keep the dial at zero and run for at least twenty minutes, and you can make an imprint in just 3 seconds, but we are running the reverse process of the 20-minute water recombination process, leaving The longer the imprinting time, the better. This can be compared to the definition of pixels. The more pixels in the image, the more data the image contains. The longer the imprinting time, the greater the information saturation. Once the imprinting is completed, you can start using frequency water to treat .

For the steps of this process, please refer to the youtube video below:

Reference link: https://berkanalabs.store/blogs/radionics-blog/basic-radionic-copying

If some curl grubs are found in the soil of your potted plants, you can try to use Spooky2 remote device to eliminate them. You firstly collected about 10 larvae, put them between the tape in the remote device, and then started to run Spooky Spectrum Sweep (R) (as below diagram), about 20 hours later, check them, if some of them are struggling and are not very active, this may be evidence of effective.

On Spooky2 Remote, we recommend running them 24 hours a day for at least 3 days (or even 1 week). Normally, you will keep running them until your symptoms disappear or you are sure that these frequencies are not working for you. On Spooky2 Contact, we recommend at least 2 times a day for about 3 days (unless your symptoms disappear and you can stop at this time), once is not enough.

If you are treating a lung disease with a large amount of congestion, please be aware that it may cause congestion and relaxation and cause coughing, and it may cause suffocation. If it is severe, please suspend Spooky2.

Scoliosis is a place where the spine is twisted and bent to one side. It can affect people of any age. Most cases of scoliosis are mild, but some spinal deformities may become more severe and cause disability. It is impossible to know what causes scoliosis, although it seems to involve genetic factors, and this disease often occurs in families. In addition, people with spinal injuries or infections may also cause scoliosis. Scoliosis can be improved with treatment, but if the symptoms are mild, treatment is not always needed, and only a few people may need surgery on the spine.

The following Youtube frequency audio will help relieve your back pain caused by scoliosis. We recommend listening at least 2-3 times a day, keeping the volume at a comfortable level to prevent any hearing damage and make sure you have enough lemons Water or purified water to flush toxins in your body.

Spooky2 plasma equipment is very good at killing mites, and its methods are as follows:

1. First of all, quit junk foods such as meat, dairy products, vitamin B-12, etc., which can feed mites and cause acne on your face.

2. Start scanning for mites in the range of 682,000 to 878,000 with Spooky2 BFB, and run them over and over again until the scan hits no longer appear. After the mites are dealt with, bacteria frequencies will be run, because this is also the cause of the outbreak. Perform a BFB scan and view the reverse lookup of the results to find the frequency of the listed mites, then note these frequencies, delete all other frequencies and save the mites frequency. Run those with Plasma, this should solve the problem. There are many types of mites and they are usually difficult to kill. Run all other frequencies and their equivalent harmonics (non-mite frequencies). These frequencies may annoy them and kill them less effectively.

3. In addition, to run the Lyme&Morgellons program, you can also use the remote control and converge the frequency captured by the BFB scan to the JW-Killing program of the remote control. All mites with the same DNA will be killed.

4. Next, use colloidal silver and tea tree oil to kill the mites in contact. This will make the “acne” and inflammation caused by the mites/bacteria disappear.

5. You can also try the frequency of the essential oils mustard and clove, or make a coconut oil-based topical cream with mustard powder and clove essential oil, which may also be useful.

Hope these methods are useful to you.